Shawnee, KS · Open 7 AM to 10 PMCall: (913) 386-2039

Garage Door Track Repair in Leawood, KS

The tracks guide every roller on the door. A bend of a fraction of an inch can make the whole door bind.

A garage door track looks simple, two steel rails with a curve at the top, yet it has to be parallel to its twin, plumb, level and spaced correctly from the door. Nothing in the geometry forgives a bump. A car that clips the lower end, a loose bracket, or years of vibration can pull a rail out of position and leave the rollers dragging.

We look at the track along its full length: bends and dents, bracket bolts, the gap between the roller and the rail, and whether the two sides are parallel. A light bend can often be straightened and the track re-secured; a creased or kinked rail should be replaced. Either way the track is re-aligned afterwards so the door stops fighting itself.

Signs the track is the problem

  • A visible bend or dent in the lower part of the rail
  • Rollers that grind, jump or leave the track at a certain point
  • A door that binds halfway or tilts as it rises
  • Track brackets pulling away from the wall, with loose or missing bolts
  • A gap between the door edge and the weather seal that changes along the opening
  • Marks where rollers have been rubbing the side of the rail

Vertical and horizontal sections

The vertical rails take the most abuse near the floor, where cars and bins tend to bump them. The horizontal sections are hung from the ceiling and can sag where the mounting has loosened. We check both, and we look at how the brackets are anchored to the framing, since a track is only as stable as its mounting.

Steel track and hardware stacked and ready for a garage door job
Two technicians with ladders handling door sections inside a garage
Technician on a step ladder at the overhead spring of a garage door, with track sections on the floor

Straighten, secure, realign

Step 1

Support the door

The door is held securely so the track can be loosened without risk.

Step 2

Inspect the rails

We sight along both tracks, measure spacing and check every bracket for looseness.

Step 3

Straighten or replace

Light bends are corrected; creased tracks are replaced, and brackets are re-anchored.

Step 4

Align and test

Both rails are set parallel, rollers are checked and the door runs through a full cycle.

A door that has already left its rails is covered under off-track repair. If the rollers wore as the track bent, see roller replacement, and for sections damaged in the same impact see panel replacement. See the starting price on the pricing page.

Track repair pricing

Track Repair & Off-Track Door per door
From $150
Diagnostic Service Call with a completed repair
$0

The starting price is per door. The final number depends on whether the rails can be straightened or must be replaced, and we confirm it on site.

Get My Exact Quote All prices →

Track questions

Can a bent track be straightened?
A light bend sometimes can. A crease or kink should be replaced, because a weakened rail may give way under load.
What is the difference between track repair and off-track repair?
Track repair fixes a rail that is bent, loose or out of line. Off-track repair is for a door that has already come out of its rails, which often needs the track and the rollers looked at too.
Why are my brackets loose?
Vibration and heavy use loosen the bolts over time, and sometimes the wood they are anchored to has worn. We check the framing as well as the bolts.
Where we repair tracks

Track repair across Johnson County

Contact Us

Contact Fountain of Mission

Describe the problem in a few words and we will get back to you. Starting prices for the common repairs are on the pricing page, and your exact figure is confirmed on site before work begins.

Fountain Garage Door Repair Expert of Mission
11501 Shawnee Mission Pkwy
Shawnee, KS 66203

Phone: (913) 386-2039
Email: info@fountaingaragedoorrepairmission.com
Hours: Open 7 AM to 10 PM, 7 days a week

Get My Estimate ☎ Call (913) 386-2039

☎